AG111 Data & Specs.

AG111 Test Data & Specifications

TEST DATA

SALT SPRAY, 5% (ASTM B117)

2 coats Master Series permanent rust sealer primer and one coat AG 111 finish coat applied to a rusted panel and scribed with an "x" through center plate. After 14,000 hours of exposure only slight undercutting at spots along the "x" was noted and this was less than 1/32 undercut. Total film thickness 8.0 mils approximate.

OUTDOOR EXPOSURE: Two coats Master Series silver permanent rust sealer, one coat AG 111 argent blue applied to the Pittsburgh Homestead High Level Bridge. At the end of 14 years, less than 5% corrosion was noted.

Tabor abrasion (CS-17 1000 gms.)

1000 cycles	15 mgs.
Pencil hardness	2 H
Flexibility (ASTM D-222)	Pass 1/8"mandrel bend
MEK Double Rubs, 48 hr. cure	Pass 100
Gardener Impact	160 in. lbs. direct and reverse

Chemical Resistance - EXCELLENT

90 days immersion is excellent, 60 days is good, 30 days is fair. Tests were run in total immersion.

EXCELLENT- 90 DAYS	GOOD- 60 DAYS
Hydrochloric Acid 10%	Sulphuric Acid 30%
Ethylene Glycol	Phosphoric Acid 50%
Sulfuric Acid 10%	Lactic Acid 85%
Ethyl Acetate	Oxalic Acid
Methyl Ethyl Ketone	Toluene
Nitric Acid 10%	Xylene
Caustic Soda 40%	Methanol
Ketone Ammonium	Ethanol
Perchloroethylene	Acetone
MIL-E 23699 Hydr. Oil
Methyl Isobutyl	FAIR- 30 DAYS
Chlorate 30%	Ammonia 10%
Tricresyl Phosphate
Skydrol A500	POOR- less than 30 days
Oxalic Acid 10%	Methylene Chloride
JP-4 Jet Fuel
Citric Acid
Gasoline

Technical Specifications:
Volume Solids	60%
Weight Solids	50%
Film Thickness	MIN. 1.5 mils per coat
Film Thickness	MAX. 3.0 mils per coat
Theoretical Coverage @ 2 mils DFT	Covers 480 sq. ft. / gallon
Drying Time @ 75' 50% RH:	Touch, 1 hour, recoat 3 hours
Potlife	6 hours
Min. Application Temperature	25'F or within 10' of dew point
Thinner/Solvent	MCT 101
Primer	Master Series Silver
Service Temperature	-40'F to 250'F
Fire Resistance	Self extinguishing (of coating)
Shelf Life	2 years
Please note: When recoating AG 111 beyond 7 days, scuff previous coat with 400 dry.

Precautions:

The only solvent that can be used with AG 111 is MCT 101. Spray gun must be flushed with MCT 101 prior to use to prevent contamination and fish eye. The use of tack rags is not recommended. If recoat time goes beyond 7 days, scuff before recoating with #400 paper.

Harmful, or Fatal if Swallowed
If swallowed, do not induce vomiting. Call physician immediately.

Eye Irritant-Wear eye protection. In case of contact with eyes, flush repeatedly with water and contact a physician.

Difficult to Remove from Skin- Wear gloves and protective clothing. Do not attempt to remove cured coating on skin with solvent. Soak in warm, soapy water. Barrier creams are recommended. Wherever possible, cover with protective clothing.

Combustible- Keep away from heat, sparks, and open flame.

Top of Page

Contact: Webperson with questions or comments about this web site. To order by phone call 800-343-9763
Last modified: 04/05/08 All PRICES QUOTED IN U.S. DOLLARS
Copyright © 2003 by Halon Marketing, LLC All rights reserved.